Tag Archives: Washing Machine Repair

Top 5 Tips For When The Washer Won’t Run

washer

So let’s face it, when we’re stuck with house chores and appliances don’t work, it seems like a day off. Only to realize, you’ll have to wear the same dirt shirt to the board meeting for the third or fourth time this week! Good luck with that! But to make sure you don’t show up in smelly, gross clothes, Appliance Repair Medic helps you to find out about your washer’s issues as much as you can, easily.

1. Check to be sure the washer is plugged in. This seems so simple, but repairmen get paid when that’s all it takes to make an appliance work. Plugs can get bumped loose by animals or fallen objects. If that doesn’t work, move on to the next item to check.

2. Once you’ve made sure the washer is properly plugged into the electrical outlet and it still won’t run, it’s time to check your central home electrical box to see if a fuse has blown or a circuit breaker has tripped. You may be able to replace the fuse or turn the breaker back on. If this happens frequently, call an electrician immediately!

3. If you’ve established electrical power, the next thing you need is water. Be sure the water valves are open. You should have two valves: a hot and a cold. They may be marked or signified by a red/blue knob or switch. Even if you always wash in cold water, some washers won’t operate unless both valves are open. If your machine is getting water but it fills very slowly, you may just need to open the valve more. A simple cleaning may do the trick to get your washer working again.

4. Loud noises occur usually if the washer has been loaded improperly or the laundry has shifted during the cycle. If the thumping occurs during a cycle (usually the spin cycle), simply stop the machine and redistribute the wet clothing. If your washer is making squealing or screeching noises, this indicates an internal mechanical problem that will require a service call. If after rebalancing the load of wet clothes the washer is still noisy and vibrates, the washer is now off-balance. You must take steps to level the washer, or it will never be quiet and further damage can occur.

5. Check if the washer’s hose connections to the hot and cold water valves. Use a dry hand or a paper towel to run down the length of each hose. If you find any dampness, tighten immediately. If the hose appears to have small splits, replace immediately. A burst water hose is a huge mess and damages walls and floors. Washer hoses should be checked and replaced regularly to prevent this problem. Pay attention to where the puddle is located, whether in the front of the washer or back of the washer. The location will give you a hint as to what to do next.

Tip 6: Clothes Are Too Wet After Final Spin Cycle

If your clothing is still quite wet after the spin cycle, first check to see if the drain hose is kinked or crushed. If your washer “dances” during cycles, it may have moved and kinked the hose. The water pump may be clogged with lint or a small object. If the pump isn’t allowed to work freely and properly, the water drains out too slowly and leaves your clothes wet. Clean it out (this does not require removing the pump). Even a little lint can slow the draining. If that is not the problem, the drain hose could be clogged with lint or hair. It can easily be cleaned with a thin, long-handled brush. Pet shops carry the brushes to clean aquarium tubes if you can’t find one at the hardware store.

Tip 7: No Clue What’s Wrong with the Washer

You know that manual you threw away without a single glance at it, the one you practiced your signature on or the one you took phone numbers down on? Yeah, that one. Get it out and read it! You may just find the answer to your question. If you don’t have the manual, visit the manufacturer’s website or one of their official sites to download a manual for your specific brand and model. It may take a little time but it’s much less expensive than a repair call.

Hopefully, these tips could help you. However, if the washer still doesn’t work, we suggest you give it a smack on the head! Actually, no, that only somehow works for remotes. But, if you ever want to get your washer repaired in the company of some friendly professionals, we suggest you head straight to Appliance Repair Medic in NYC! Have a great day!

5 Things You Must Consider Before Buying a Washing Machine

5 Things You Must Consider Before Buying a Washing Machine

Appliances are not luxuries nowadays rather they are a necessity. Whether it is a washing machine or dishwasher, every appliance has become an integral part of our everyday life.

Today, in almost every home you will find a washing machine as it saves a lot of time and makes the work easy.

And those who don’t have it must be craving for it. If you are a first-time buyer, you must consider a few things before buying a washing machine.

Semi-Automatic or Automatic

Which one is better for you – Semi-Automatic or Automatic? If you do not know the difference between the two, no worries here is the description of the two.

  • Semi-Automatic

Semi-automatic machine you will contains two tubs, one for washing clothes and the other one for drying the clothes. Once you are done with the wash cycle, take out the wash clothes with your hands and put them in the other tub for drying.

  • Automatic

In a fully automatic machine, put inside the clothes and wait for the process to complete, which is notified with an alarm sound. The washing machine with auto feature contains the cycle of washing, rinsing and drying the clothes.

Related Articles: Tips to Make Your Dryer More Efficient

So, now you have to decide which one is better for you from the two – Semi-Automatic and Automatic machine.

Front Loading or Top Loading

At present, you will find two main styles in the market – the front loading and the top loading styles. Top loading style is the most commonly used one. However, when it comes to the latest models, many brands offer front loading options.

If you consider the energy efficient one, then you must choose the front loading one. And in case you have a tight budget, you should choose a top loading one as it is relatively lower in price. It also cost washing machine repair in NJ lower as compared to a front loading washing machine repair cost.

Size and Capacity

The most important thing a buyer must consider while buying a washing machine is the size and capacity of the machine. Check the size of the washer tub and its maximum capacity to load the clothes per cycle.

No matter if you have semi-automatic or automatic machine, make sure when you put clothes inside, there should be enough space for the clothes to move and rotate. The machine with a large capacity is useful when it comes to washing bed covers, curtains, etc.

Consider The Material of Washing Machine

While buying a washing machine it is necessary to check out the material of a drum. Normally, it is available in stainless steel, porcelain enamel, and hardened plastic.

According to most people, plastic tub is better as Enamel rusts and chips. However, stainless steel tubs consider as the best option. Because stainless steel is rust resistant, capable of bearing high spins and also it is long-lasting.

Check Out The Safety Features

While buying a washing machine, you must check the safety parameters carefully. A few things that you must check are:

  • Auto restart
  • Stability while spinning
  • Child lock
  • Water level control
  • Foaming over protection
  • Overheating protection

Bottom Line

So, these are a few things you must consider while buying a washing machine in order to save washing machine repair in near future. If you are based in NY or NJ area consider us to appliance repair in NY and NJ.

Tips for Common Household Appliance Maintenance

home appliance repair

Everything needs proper care and maintenance, whether it is your health or your appliances. Good care of the appliances can save thousands while bad care of appliances can cost you a lot. Somewhere in the corner of our heart, we all have that fear. What if the washing machine breaks in the middle of a cycle? What if the oven stops working just before a large holiday meal?

What we don’t realize is that these and other major appliance breakdowns can be avoided with just a little care and maintenance.

Here are the few tips for Appliance Maintenance.

1. Clean or replace dirty from the dishwasher filters

In order to maintain dishwasher, metal-mesh grease filters need to be washed by hand in the soapy water or run them through the dishwasher. In case you need experts’ advice, you can approach washer repair ny. And remember, you don’t need to wash paper filters or charcoal. Better replace them instead. You can also have a look at these factors to know before hiring any dishwasher repair services

2. Verify your oven door has a tight seal

The oven can lose more than 20 per cent of its heat if it does not have a proper seal. In result, food will take longer to cook or cooks unevenly. Therefore, you need to check the seal’s condition of the oven door. You can check the fiberglass gasket or rubber around the perimeter of the door. In case there are any broken, deformed areas, or you find any leak while closing the door, it is advisable to replace the seal or contact with our wolf oven repair experts.

3. Clean stovetop drip bowls

Remove wet bowls from under the burner and soak them in a cleaning solution for around five minutes. Then go for a wash and replace them. It is advisable to clean wet bowls instantly after spills. In case spills burn into the bowls, time to replace them.

4. Clean coils in your refrigerator

Dirt and pet hair can block the refrigerator coils. Furthermore, it can restrict the air flow and cause the refrigerator to work harder to keep cool. It is advisable to clean the coils and you can do it with the handheld vacuum. The location of refrigerator coils varies by model, but in most cases, it is located behind the kick plate (the front panel near the floor) or at the rear of the fridge. In case you find defrost heater or any other part faulty, you can approach professionals for refrigerator repair.

5. Change your refrigerator water filter

Filters that don’t efficiently remove toxins could expose you to harmful water. In such a situation, experts’ advice to change the filter after every three to six months. In the end, it depends on water usage. However, Guidelines for changing the filter vary by model, but most are as simple as turning the filter a quarter inch and locking it in place.

6. Clean your dryer exhaust

Hair in the dryer exhaust not only reduces appliance efficiency, it is a fire hazard as well. To clean, loosen the clamp and pull the exhaust off the back of the dryer. Use your hands to clean large clumps of lint from the tubing and the hole in the back, or in case you can’t reach, you can use straightened coat hanger. In the end, vacuum it and reattach.

7. Inspect washing machine hoses

Most washing machine floods are caused by leaks in the hose. Check if there is any cracks, leaks, or weak spots the pipes that connect to the back panel on your washing machine. And if you find any defect, go for washer repair. In most cases, expert’s advice to replace the hoses every five years.

8. Clean your air conditioner filter

Dirty filters or clogged restrict air flow, reduce energy efficiency as well as the air conditioner lifespan. Therefore, filters should be cleaned between two to four weeks. To clean the filter, you have to remove the front panel of the unit. Clean the dirt as much as possible with vacuum. You can go for the replacement of the disposable filter as well.
Bottom Line

So, if you want to save money on the maintenance of your household appliances, start following these tips.

What Signs Indicates Your Washing Machine Needs Repair

Washing machine repair service

Nowadays, home appliances give every individual a reason to smile because of the comfort and efficacy they give. A washing machine is one of the crucial appliances as it allows people to have clean and fresh sniffing clothes every time.

No matter whether you have latest LG front loading washer or any other brand. Over the time, your washing machine stops functioning properly as it should and you should have to consider LG appliance repair NJ.

Typically, the washing machine gives a few warning signs that something is incorrect. However, just because you hear a bizarre sound during the random wash cycle it does not always mean machine need a repair.

Here are some signs to determine if your washing machine needs attention:

  • The washing machine is making an extreme noise

Every machine makes some noise. But it should only concern when it is continuous as well as unusually loud. Actually, it is easy to fix and there is no need to call out a technician. But sometimes, it can be a sign that something is wrong with the washing machine.

One solution to stop the excessive noise is to stop the wash cycle and rearrange the clothes. If the problem is not get solved then you should consider calling a technician for Viking appliance repair NJ. It is also advisable to check the warranty material to see if this type of service is covered. An excessive noise indicates a problem with the drum and the seal on the tub. Therefore, do not let this repair go too long.

  • Excessive leaking

If your washer ever starts leaking, then it is the most obvious sign that it has a problem. Actually, leakage problem is the result of overflowing or a loose connection. As the water hose in the back of washing machine distress from years of wear and tear and has become slack.

You can also consider if pipe tightening or replacing hose can fix the problem for you. And if not then you can call a repair technician in order to determine the true cause of the leak.

  • The washer is not pumping or spinning

Sometimes, the washing machine fails to pump water in or out and spin. This can happen with the motor running and if it doesn’t it is likely due to a failed lid switch. The switch is close the door frame inside the washer. If it is defective then it requires to be replaced or there is a need for Subzero appliance repair professional.

  • Clothes are still wet

After a spin cycle, the washer is not functioning appropriately might leave the clothes wet. The reason could be the motor coupler. In fact, it differs according to the brands. For instance, with GE appliance it may be a damaged clutch while with Maytag it can be worn out the belt.

  •  Washer shakes during operation

The washing machine does a bit of vibrating at certain points in the wash cycle. While the entire machine springs, shakes and vibrates, it is a sign that something is wrong. Have you shifted your home recently?

Also read these 8 obvious signs your refrigerator is due for maintenance

If so then there is a chance that washer’s shock absorber could have come loose. This could be the possible reason or maybe the problem is with machine suspension. Hire a whirlpool appliance repair professional to bring your washer to its normal operational mode.

  • Washing machine won’t agitate

The agitator moves the clothes around in the water earlier in the spin cycle. And if the washing machine does not agitate, the reason can be a worn belt, worn clutch, the coupler on the motor, a faulty lid switch, a failed drive motor etc. Sometimes you can also find a black substance on the ground beneath the washer. This indicates that clutch needs replacement.

  • The washer seems to be off balance

Randomly distributing clothes in the washer causes the inside tub to become unstable. You can notice this while spinning as whole the washing machine shake as well as make an awful noise. It places a lot of pressure on the machine and also causes the internal parts to break down a lot sooner than normal. Hence, if your washer is doing the same thing then you should go for washing machine repair services.

  • Water does not fill the drum

If the drum of your washing machine is not filling up, there may be a delayed cycle selection, twist in the hose or an issue with the hot or cold water spigots. You should check for all these three issues. If you did not find any of the three issues. Then there could be some sort of difficulty with the water valve that requires a repair technician attention.

  • Other Issues

If your washing machine stop working suddenly and you do not have any idea what happened. Only a repair technician can identify the concern and repair it so you can get back to your washing.

Wrapping Up

These are some signs that indicate your washing machine needs repair. While you can overhaul certain household appliances yourself, not every washing machine troubleshooting is that easy. You may need the help of repair technician in order to fix your washing machine properly.

Although hiring a professional to LG appliance repair NJ will cost you money than doing the job yourself. But if you are not actually sure of the problem may charge you even more. Hence, rather than washing clothes by hand or giving to the laundry mat, it’s a wise decision to get the issue fixed by Appliance Repair Medic as soon as possible.

Washing Machine Repair Services – 3 Tips to Choose the Best Service

Washing Machine Repair Services

Have you been looking for washing machine repair service such that you could get a quality service for your costly device? Either its human being or machine both need medication and repairing from time to time to function smoothly. As each time due to friction and wear tear in machine parts they need a proper servicing that could help them to provide efficient lubricant and other technical servicing.

Even more when you are looking for washing machine repair you also have to consider three simple tips that could help you to avail best services. Such hat no compromise could be made by either side so that your machine could work for long span without any obstacle in performance:

Trust Worthy

Always go with such servicing company whom you can feel like trusting and are always avail on your first call. But before this you have to check their reputation, feedback from other customers and their service record to make sure that they are capable enough to provide a quality service each time. No matter you are going with most expensive for a small local service provider, as it all depend on your satisfaction level that you deserve from your customer.

repairs washing machine by Appliance Repair Medic

Don’t consider price alone

When you are going with washing machine repair never consider price alone, though it’s important to go with affordable washing machine services but that will never make sure that you are getting the desired service. You have to make the comparison between the reputation, availability, and price of the different service provider. You alone can make an informed decision regarding which company is best for your washing machine repair needs.

Concern other

Last but not the least when you are going with Washing Machine Repair Services you have to have to make a list of some service provider of your area. Just don’t restrict yourself to one provider or someone other just for the sake of not willing to look others. You have to make sure that what you are paying and what you have to pay when you look for some other service provider, and never judge that the more expensive will provide you more quality service.

So from the next time when you are searching for washing machine repair services then you must go with these three tips to choose the best service. Even more try to go with your local service provider as that will save your more cost and fuel as well as ensure to get electric service that are latest in market and are far better than other services